Can You Use A Belt Sander On Decking

In this article, I will discuss the use of belt sanders for decking refurbishment. Many people are concerned about using belt sanders on their decks because they can remove a lot of surface material.

However, if the job is to remove the surface finish quickly, then a belt sander is the best tool for the job.

I will cover topics such as understanding belt sanders, sanding techniques, choosing the right sandpaper, and refinishing the deck.

By following these guidelines, you can make the job of refurbishing your decking as simple and fuss-free as possible.

Key Takeaways

  • Belt sanders are an effective tool for quickly removing the surface finish of your decking.
  • Start with a coarse grit sandpaper to remove the top layer of finish, then move on to a finer grit for a smoother surface.
  • Always go with the grain of your decking boards and use a diagonal angle only for stubborn stains.

Video

Can You Use Belt Sander on Decking

If you’re looking to refurbish your decking, using a belt sander is the quickest way to remove the initial half a millimeter of surface finish. With a large surface area to tackle, it’s important to make the job as simple as possible.

While belt sanders are designed to remove material, you only need to remove the surface finish. To do this quickly, start in a small corner of your decking to test out the belt sander. As soon as you’ve removed the top layer of finish, stop sanding. Use a harsh, coarse grit sandpaper (60 grit or 80 grit) to make it easy to remove the top layer. You can always put a finer sandpaper in after to finish the job.

It’s important to go with the grain of your decking boards when using a belt sander. If there are stubborn bits of stain, you can possibly use your sander across the grain or at a diagonal angle. However, it’s important to go back over with your belt sander and go with the grain as your final pass to avoid scuff marks in your wood.

For refinishing a deck, a belt sander is the only sanding tool you need. Start with a really coarse grit like 60 or 40, go over it with your belt sander to remove the surface finish, then put a finer sandpaper in there, like a 120 grit, to give the deck a final sand. This way, you’ve removed the surface finish with as little fuss and quickly passed over the wood without sanding away the grooves.

Remember to not let your sandpaper sit on the raised and hollowed out areas as you get going. As you start working your way around your deck, you’ll find it easier to remove the finish with a belt sander.

Preparation for Decking Refurbishment

To refurbish a decking, I recommend using a belt sander as it is the quickest way to remove the initial half a millimeter of surface finish. If your deck has been treated with stain or varnish that is starting to flake off, using a belt sander will make the job easier and quicker. However, it is important to note that belt sanders are designed to remove material, so it is crucial to start in a small corner of your decking and test out the belt sander. As soon as you have removed the top layer of finish, stop sanding and move on to the next section.

When using a belt sander on your decking, it is best to go with the grain of your decking boards. If there are any stubborn bits of stain, you can possibly use your sander across the grain or at a diagonal angle. However, it is important to go back over with your belt sander and go with the grain as your final pass to avoid scuff marks in your wood.

For a decking refurbishment project, a belt sander is the only sanding tool you need. I recommend starting with a really coarse grit like 60 or even 40 to remove the surface finish, then using a finer sandpaper like 120 to give the deck a final sand. This way, you have removed the finish with as little fuss as possible and have a nice surface to take the new stain. It is important to not let your sandpaper sit on the raised and hollowed-out areas as you start working your way around your deck.

Understanding Belt Sanders

When it comes to refurbishing a decking, using a belt sander is the quickest way of removing the initial surface finish. Belt sanders are designed to remove material, so it is important to be aware that they can take quite a lot of surface material off. However, if the job is to remove the surface finish, then using a belt sander is the best option.

To start, it is recommended to use a harsh coarse grit sandpaper in the belt sander, such as 60 grit or 80 grit, to quickly remove the top layer of finish. As soon as the finish is removed, move on to the next part of the decking. The hardest part of any sanding project is getting rid of the old finish, so make life easier for yourself by using a harsh sanding grit.

It is important to test out the belt sander in a small corner of the decking before starting. If there are any stubborn bits of stain, it is possible to use the sander across the grain or at a diagonal angle. However, always go back over with the belt sander with the grain as the final pass to avoid scuff marks.

To get the best results, start with a coarse grit sandpaper to remove the surface finish, then use a finer sandpaper, such as 120 grit, for a final sand. This will bring the wood up nicely without taking too much off the decking or sanding away the grooves. The goal is to remove the finish with as little fuss as possible and quickly pass over the wood.

Overall, if I were refinishing a deck, I would be perfectly satisfied that the only sanding tool needed is a belt sander. It is important to remove the finish with as little fuss as possible and quickly pass over the wood.

Sanding Techniques

For refurbishing a deck, I recommend using a belt sander as it is the quickest way of removing the initial surface finish. You can quickly work your way around the deck with as little fuss as possible and slowly remove your stain or treatment.

People are often concerned about belt sanders taking off too much surface material, but if the job is to remove the surface finish, then you want to do that as quickly as possible. To start, use a harsh coarse grit sandpaper in your belt sander, maybe 60 grit or 80 grit, and make it easy for yourself to remove the top layer. As soon as the finish is removed, move on to the next section.

If you decide to use your belt sander on your decking, I recommend going with the grain of your decking boards. If there are any stubborn bits of stain, you can possibly use your sander across the grain or at a diagonal angle. But always go back over with your belt sander and go with the grain as your final pass to avoid scuff marks in your wood.

For a deck refinishing project, a belt sander is the only sanding tool you need. Start with a really coarse grit like maybe 60 or even 40, go over it with your belt sander to remove the surface finish, then put a finer sandpaper in there, maybe something like a 120, to give the deck a final sand. This way, you’ve used your coarse grit to remove the finish, and your 120 grit to bring the wood up nicely. You’ve not taken too much off the decking, and you’ve not sanded away the grooves.

Remember, remove the finish with as little fuss as possible, quickly pass over the wood, and don’t let your sandpaper sit on the raised and hollowed-out areas as you get going. As you start working your way around your deck, you’ll find it easier.

Choosing the Right Sandpaper

When it comes to refurbishing a decking, using a belt sander is the quickest way of removing the initial surface finish. This can be achieved by using a harsh coarse grit sandpaper in your belt sander, such as 60 grit or 80 grit. By doing so, you can remove the top layer of finish quickly and with as little fuss as possible.

It is important to note that belt sanders are designed to remove material, so it is crucial to start in a small corner of your decking and test out the belt sander. As soon as you have removed that top layer of finish, stop sanding. There is no need to sand anymore.

If you do decide to use your belt sander on your decking, it is recommended to go with the grain of your decking boards. However, if there are any stubborn bits of stain, you can possibly use your sander across the grain or maybe at a diagonal angle. If you do go diagonally or across the grain, it is important to always go back over with your belt sander and go with the grain as your final pass. Otherwise, you will have scuff marks in your wood.

For a decking refinishing project, a belt sander is the only sanding tool you need. Start off with a really coarse grit like 60 or even 40, go over it with your belt sander, remove the surface finish, then put a finer sandpaper in there, such as 120 grit, and give the deck a final sand with 120. This way, you have used your coarse grit to remove the finish and your 120 grit to bring the wood up nicely without taking too much off the decking or sanding away the grooves.

In summary, to choose the right sandpaper for your decking refurbishing project, use a harsh coarse grit sandpaper in your belt sander to remove the surface finish quickly and with as little fuss as possible. Always go with the grain of your decking boards and use a finer sandpaper for a final pass. By doing so, you can remove the finish with as little fuss as possible and give yourself a nice surface to take the new stain.

Refinishing the Deck

For refurbishing a deck, I recommend using a belt sander as it is the quickest way of removing the initial surface finish. When using a belt sander, it is important to start in a small corner of your decking and test out the belt sander. As soon as you have removed that top layer of finish, stop sanding. You can then put a harsh coarse grit sandpaper in your belt sander, maybe 60 grit or 80 grit, to make it easy for yourself to remove the top layer.

If you do decide to use your belt sander on your decking, which I would recommend as the quickest way of refinishing it, always go with the grain of your decking boards. If there are any stubborn bits of stain, you can possibly use your sander across the grain or maybe at a diagonal angle. Whatever technique works for you is all well and good.

I would start off with a really coarse grit like maybe 60 or even a 40. Start with a really coarse grit, go over it with your belt sander, remove the surface finish, then put a finer sandpaper in there, maybe something like a 120, and give the deck a final sand with 120. That way, you’ve used your coarse grit to remove the finish, and your 120 grit to bring the wood up nicely. You’ve not taken too much off the decking, you’ve not sanded away these grooves, you’ve just literally removed the surface finish.

Make sure to not let your sandpaper sit on these raised and hollow areas as you get going. As you start working your way around your deck, you’ll find it easier. The hardest job of any sanding project is getting rid of that initial old finish, so make life easier for yourself, use a harsh sanding grit, and get rid of that top finish. As soon as the finish is removed, move on to the next.

Always go with the grain as your final pass in any belt sanding project. I’d be perfectly satisfied that the only sanding tool you need really is a belt sander.

Final Recommendations

For refurbishing a deck, I would recommend using a belt sander as it is the quickest way of removing the initial surface finish. To make the job as simple as possible, start in a small corner of the decking and test out the belt sander. As soon as you have removed the top layer of finish, stop sanding. You can then put a harsh coarse grit sandpaper in your belt sander, maybe 60 grit or 80 grit, to remove the top layer of finish quickly.

It is important to note that belt sanders are designed to remove material, so be aware that they can take quite a lot of surface material off. However, if the job is to remove the surface finish, then using a belt sander is the best option. Once you have removed the surface finish, you can then refinish your decking.

When using a belt sander on your decking, try to go with the grain of your decking boards. If there are any stubborn bits of stain, you can possibly use your sander across the grain or at a diagonal angle. However, always go back over with your belt sander and go with the grain as your final pass to avoid scuff marks in your wood.

For the sanding project, a belt sander is the only sanding tool you need. Start with a really coarse grit like 60 or possibly even 40. After removing the surface finish, put a finer sandpaper in there, maybe something like a 120. Give the deck a final sand with 120. That way, you’ve used your coarse grit to remove the finish, and you’ve used your 120 grit to bring the wood up nicely without taking too much off the decking or sanding away the grooves.

In conclusion, removing the finish with as little fuss as possible is the key to refinishing a deck. A belt sander is the quickest way to achieve this, and by following these recommendations, you can make the job as simple as possible.

Sam Wood

Wood by name, wood by nature. I am a fully qualified, time-served, award-winning joiner with an NVQ Level 3 in Carpentry and Joinery as well as an HNC in Construction. Beyond my joinery qualifications, I have also earned a degree in building surveying. I believe these qualifications make me perfectly positioned to provide expert advice on many different areas of DIY as well as share all of the tips I have picked up in over a decade working on building sites!

More Reading

Post navigation

Leave a Comment

Leave a Reply

Your email address will not be published. Required fields are marked *